How to remove a pocket door

How to remove a pocket door | Step-By-Step Guide

Pocket doors are typical in most new homes, but as with all conventional home furnishings, they wear out and become obsolete, necessitating the replacement of new entries. Knowing how to remove a pocket door on your own could help you save money. However, when learning how to draw a pocket door, an overview of the whole process might make it look not very easy. 

Steps required to learn how to remove a pocket door are pretty simple. All you have to do is locate the retention clips and look for a release mechanism to get started. The door may need to be kept in place; it’s also possible that it’ll be pretty heavy. As a result, a helping hand can be beneficial as you go forward. FinallyRelease the clip by sliding the door until it sticks out about 3 to 4 inches; you may need a screwdriver for this. 

The clips on some doors must remain open until the door is taken from the hanger. Then, lift the door slightly until the rollers come off to release it from the track. For more detailed explanations, tips and tricks read to find out more. Reading and following the instructions in this article will save you a great deal in repair costs.

What Are Pocket Doors?

Before learning how to remove a pocket door, let’s gain some insight on the subject topic.

A pocket door is a unique door that slips straight into the sidewalls, as seen in modern structures. However, instead of swinging outwards or inwards like a typical door, the pocket door slides sideways in.

In the opposite direction, this method of opening and closing saves a lot of room in both ways.

As a result, the half-round area in front and back would no longer be required to close and open a door. You can utilize the site directly behind the door for your chair or table because there is no requirement for such a room.

Pocket doors are typically seen in places of the home where there is a desire to optimize space. For example, pocket doors are frequently installed in the bedroom, bathroom, or busy living room. Next, we will be addressing the steps on how to remove a pocket door.

How To Remove A Pocket Door
How to remove a pocket door

How to Remove a Pocket Door – Step By Step Guide

You’re just a few steps from learning how to remove a pocket door. All the critical steps are outlined below. Follow them to reach your desired results.

Step One: Release the Pocket Door Hangers

Pocket door hangers are linked to rollers that glide down a track, allowing the door to move back and forth. The jambs on either side of the door prevent you from rolling it out the other end. Hangers are designed to include a retention clip that secures the door hanging hook to the bolt for the rollers. 

Unfortunately, each manufacturer employs a unique hanger and clip. Before you attempt to remove the door, you must first locate the clip release. To push the release lever, you may need to use a screwdriver. Some clips need you to hold them open until the door is removed from the hanger.

Step Two: Remove the door stop’s caulk.

Next, completely open the door to gain access to the door stop, where you will find the caulk. Then, gently scrape off the caulk along the doorstop using a sharp object such as a utility knife or a razor. Make sure you scratch the caulk lines of the stop slowly, as any mistake will result in loss or spoilage.

Remove the wood if you won’t need it after you’ve scratched out the caulk and accessed the doorstop. You won’t use a pry bar to take down the wood if you intend to recycle it.

Step Three: Remove the Door Stop

Third on our list of how to remove a pocket door is to pull the doorstop finally.

Now that you’ve removed the caulk, the next step is quite simple. Remove the doorstop from its frame altogether. Even though eliminating the stops isn’t tricky, a pry bar will be required. You should not be alarmed if you see a doorstop fastened to the side with a nail.

What you have to do is take it out of the wood first to avoid dents. Of course, if the wood deteriorates, you will be given a replacement. Next, close the sliding pocket door so that you have enough space to lift it out of the door frames.

Step Four: Take Out the Pocket Door

When you raise the pocket door entirely off of its tracks, you’ll see there’s a component you need to open. Then, move over to the open side of the door and lift it out. Begin pulling the screen towards you when both sides are available on the same side. Attempt to carefully lift the door while pushing to draw the rollers out of their grooves. If the door is too massive for one person to open, you will want assistance. This individual would assist in pushing and pulling the door as needed.

Step five: Pull Out the Pocket Door

You can now remove the pocket door and set it aside when you’ve completed these preliminary steps. Yes, it is necessary to relocate it away from your exit. For some, this is the most challenging stage. The size of the door also determines how difficult it will be to open; you may need to seek assistance. If the track becomes embedded in the wall, you should hire a professional to remove the door. Doing it yourself may consume all of your time and energy while failing to complete the task.

How To Remove A Pocket Door
How to remove a pocket door

Tips on how to remove a pocket door

When removing a door because it’s warped, painting it will protect your replacement door from the same problem. To do so, you’ll need to know how to paint a pocket door without taking it off the tracks. Then, after you’ve mastered the technique, you may paint the four sides’ faces and edges to avoid warping.

Slide the rollers into the track after installing the hanging pocket door hardware on top of the door. Adjust the door until it is level while hanging it on both hangers. When putting drywall over the pocket, install the door grip before removing the door. As a result, apply a few coats of the drywall mixture to the joints before installing the door.

Pocket door guides should be installed on both the inside and outside of the door. You can avoid pocket door wobbles by nailing the head jambs and two-piece to either side of the door. Then, with a nail and pocket door studs, secure the door casing to the frame. The strike plate should then be installed after that.

How to Replace a Pocket Door

You may have considered how to replace a pocket door but have not fully comprehended the process because of the difficulty you’re having with your slider.

Step one: ​Removing the Door

In addition to removing the door frame, the first step in replacing a pocket door is to create a hole in the wall to provide access to the rollers and track system. You have total control over the roller and track at this point. The old door may be removed from the rollers by tilting it down.

Step two: ​Removing the Track

To replace the door’s operating components, you’ll need to remove the track system by unscrewing all of the screws holding it in place. It would help if you accounted for any gapping when installing a new track in the exact location as the old one. This may be avoided by making sure the way is level before installing it.

Step three: Shimming the Track

If you have shifted your housing or settlement over time, you may need to put shims under the track. You may screw the way into place after it is as level as possible in the header of the pocket door opening.

Check to see if your new track’s rollers need to be put before installation or if they may be placed after the way has been mounted. To prevent having to remove the trail again to install the rollers as instructed, double-check this requirement.

Step four: ​Replace Roller Hardware.

Replace the roller hardware at the top of your door while you’re at it. Rehang the door after installing the new rollers at the top. It requires a certain amount of skill to rehang a pocket door. You’ll need to align your door’s rollers with the tracks and make sure it glides back and forth smoothly.

Step five: Installing the Door and Frame

To maintain the integrity and look of your door, you may now replace the frame piece by piece. Hopefully, you were able to dismantle the frame while keeping the complete structure intact carefully.

If your old or new door is hefty, a pry bar or shims can be used to pull it into place or hold it in place while you install the rollers on the track. It’ll be a little simpler to deal with now.

This will allow you to quickly replace it and return to mending the access point you created in the wall.

How to remove a pocket door: Conclusion

This wraps up our guide on how to remove a pocket door. Spend some time learning how your pocket door works. If you need to access the roller and track installed in the wall, don’t be afraid to make a hole in it. While this may seem inconvenient, it is the only way to ensure that your sliding door functions well for many years.

4 thoughts on “How to remove a pocket door | Step-By-Step Guide”

  1. Pingback: How to demo a bathroom | Step-By-Step Guide [2021] - Tubevarsity

  2. Pingback: How to demo a bathroom | Step-By-Step Guide [2021] - Tubevarsity

  3. Pingback: 10 Best Gameloft Games for Android and iPhone of 2022: Everything You Need To Know [Video] - Tubevarsity

  4. Pingback: 10 Best Gameloft Games for Android and iPhone of 2022: Everything You Need To Know [Video] - Tubevarsity

Leave a Comment

Your email address will not be published.

Scroll to Top